Thread
:
▀▄ eas | DIY: S55 M3/M4 BMC Filter Installation
View Single Post
07-23-2014, 01:57 PM
#
1
tom @ eas
BimmerPost Supporting Vendor
8260
Rep
18,848
Posts
Drives: BMW
Join Date: Nov 2005
Location: Anaheim, CA
iTrader: (
19
)
Garage List
2018 BMW i3s
[5.00]
2010 BMW M3
[6.50]
2015 BMW M4
[6.20]
▀▄ eas | DIY: S55 M3/M4 BMC Filter Installation
A panel air filter is commonly referred to as a replacement air filter. It is installed in the vehicle's original airbox to replace the OEM air filter. It is made of high performance materials that allow for an increase in air flow along with more efficient filtration. These BMC filters guarantee containment of all impurities from as small as 7 microns, as compared to the OEM's 10 microns.
BMC air filters are produced using a full molding system that enables the characteristic red filter to be realized from a single mold with no welded joints, thus avoiding easy breakage. The rubber used in BMC air filtering systems has a long life, is very durable and has optimum adhesion characteristics to all shapes of airboxes. BMC filters are made of a multi-layered cotton gauze soaked with low viscosity oil covered with an epoxy coated alloy mesh to ensure protection from petrol fumes and oxidization due to air humidity. All BMC air filters are pre-oiled, and they can be washed and regenerated by using an appropriate regeneration kit.
Installation
BMC High Performance Replacement Air Filter (set of 2)
https://europeanautosource.com/bmc-h...r-filters.html
Tools needed
T25 Torx driver
Pocket screwdriver
10mm & 13mm Wrench (socket)
Trim Removal Tool
Installation
1. Remove compression rivet from trim cover
2. Remove plastic nuts from right bank cowl cover, note these are twist-lock design (90-degree twist)
3. Remove compression rivet from trim cover
4. Remove plastic nuts from left bank cowl cover, note these are twist-lock design (90-degree twist)
5. Remove compression rivet from strut tower brace trim cover
6. Remove Bolts securing strut tower brace (13mm), nut on coolant reservoir is 10mm.
7. Carefully remove strut tower brace and admire BMW's craftsmanship.
8. Remove bolts on right airbox with T25 torx driver to reveal filter
9. Remove filter lid
10. Remove charcoal liner with small pocket screwdriver to release tabs
11. Drop new BMC oiled filter in place. filter comes pre-oiled from factory. Reinstall filter lid
12. Pinch plastic securing mount and lift on right filter housing to move out of place
13. Pinch/remove PCV hose and remove. Remember to reinstall after filter is installed.
14. Remove bolts on left airbox with T25 torx driver to reveal filter
15. Remove filter lid
16. Remove filter lid
17. Reinstall left filter lid
Torque Specs
Airbox:
Snug to fit/hand tighten
Strut tower brace
13mm: 10-12lb-ft.
10mm: 3-5lb-ft
Enjoy! Feel free to respond to the thread with any questions.
__________________
Tom G.
|
european auto source (eas)
email:
tom@europeanautosource.com ·
web:
https://europeanautosource.com·
tel 866.669.0705 · ca: 714.369.8524 x22
GET DAILY UPDATES ON OUR BLOG
·
FACEBOOK
·
YOUTUBE
·
FLICKR
·
INSTAGRAM
Last edited by tom @ eas; 01-30-2018 at
10:59 PM
..
Appreciate
9
Dr. Who
302.50
Xtabi
1707.50
fabulousprofound
34.00
PhatLyfe
985.00
kyleb350
423.50
Jim45678
165.00
Tweet
Quote
tom @ eas
View Public Profile
Visit tom @ eas's homepage!
Find More Posts by tom @ eas